- Home
- Products
- Screens and filtration
- Internal feed screen
Internal feed screen.
A fine screen for the inlet of a treatment plant: the flow is fed to the inside of the mesh panel belt, the screenings stay on the inner face, and the wash system carries them out to the discharge instead of back into the channel.

What an internal feed screen is, and what the site still does
An internal feed screen is a fine screen for the inlet of a treatment plant. The mesh panels are carried on a frame in the inlet channel, and the flow is fed to the inside of the belt rather than to the outside: water passes outwards through the panels, the material larger than the aperture stays on the inner face, and the panels are washed on their return path so the material is carried out to the discharge instead of back into the channel. The screen is built as a fabricated channel section or as a vertical unit for a chamber, and it is assembled and tested at our factory before shipment; on site the channel or chamber and its civil works, the inlet and outlet pipework to our flanges, the power and earthing, the wash-water supply, the lifting and placement, and the screenings route away from the unit are site work.
Aperture and capacity are fixed per project, not read off a catalogue
This page publishes no single capacity or screen aperture for the internal feed screen. The clear opening is chosen from what has to be protected downstream — a pump, a grit chamber, a membrane or a discharge — and the flow the screen can pass follows from the channel width, the water depth and that opening, not from one catalogue number. We fix the channel width, the screen aperture, the capacity and the material grade from your channel survey, your design peak flow and the particle size the downstream unit needs, and our engineering issues them on the project drawing (evidence SH-IF-CAP-01, SH-IF-APERTURE-01).
Project-confirmed, not catalogue-confirmed
The channel width, aperture and capacity are confirmed per project from the channel survey and the design peak flow. No capacity figure is published because the duty is fixed by the channel and the opening, and that calculation repeats from the same inputs at sizing.
Inside feed versus outside feed: what it changes, and when it is the wrong screen
On an internal feed screen the flow is fed to the inside of the mesh panel belt; water passes outwards through the panels, the retained material stays on the inner face, and the wash system removes it from there. On an outside-feed arrangement the flow meets the outer face, and the return pass of the belt can drag material back toward the channel if the washing is not arranged to stop it. Inside feed solves that return problem for fibrous and rag-heavy flows, but it is not the right screen for every site: a very wide channel, a flow too large for a panel belt, or an inlet that cannot take a belt frame are reasons to look at a bar screen or a drum instead (evidence SH-IF-INSIDE-01).
- Choose internal feed when fibre, rag and fine material must be held on the inner face and washed out, not dragged back (evidence SH-IF-INSIDE-01).
- Look at a rotary rake screen when the duty is a coarse bar screen in a channel or at a pump station.
- Look at a rotary drum screen when a drum across the channel fits the inlet better than a panel belt.
How the wash carries the screenings out, and why they do not go back into the channel
The panels are washed on their return path. The wash system flushes the material held on the inner face into a discharge chute or a conveyor, and the panels go back to the channel clean. Feeding from the inside and washing the inner face together are what keep the screenings out of the flow on the way back: the downstream face of the belt carries no material to drag down the channel. The wash-water demand is fixed per project with the discharge arrangement, because it depends on the aperture, the screenings load and the nozzle arrangement; our engineering confirms it from the channel survey and the screenings route (evidence SH-IF-WASH-01).
Wash water and the screenings outlet are project items
The unit supplies the wash arrangement; the water supply, the conveyor or skip and the legal outlet are fixed with the order and the site permit.
Channel-mounted or vertical: the installation choice
In a straight inlet channel the screen is built as a fabricated channel section, cast into or bolted onto the inlet structure, with the drive above the covers and an inclined screw or conveyor lifting the washed screenings clear. In an inlet chamber the same screen is built as a vertical unit whose drive and discharge sit on the head frame and whose panel run hangs into the water; that arrangement suits a retrofit where the structure already exists. Installation depth, chamber clearances and the discharge arrangement are confirmed per project from the chamber drawing, and our engineering fixes them before the build (evidence SH-IF-VERTICAL-01).
Materials, corrosion and the parts that wear
The wetted parts are built in stainless steel, and the grade is chosen against the water: a standard austenitic grade for ordinary municipal and industrial duty, a higher grade where the chloride load or the process chemistry calls for it. The wear parts are the mesh panels, the wash nozzles and the drive components, and their life follows the screenings load and the wash. We confirm the grade and the wear-part set per project from a water analysis; a grade that serves a municipal inlet can pit in a chloride-rich industrial flow (evidence SH-IF-MAT-01).
What is in our supply and what stays on site
In our supply sit the screen body, the mesh panels, the drive, the wash system, the discharge arrangement for the unit and the control panel that runs it. On site sit the channel or chamber and its civil works, the inlet and outlet pipework to our flanges, the power supply and earthing, the wash-water supply, the lifting and placement, and the screenings route away from the unit. The exact split is written into the commercial offer for the project.
Acceptance is written into the contract: factory acceptance tests before shipment, site acceptance tests after installation, and a performance test on the retention at the design flow, with the aperture, the channel dimensions, the wash-water flow and the screenings route agreed for the project, the sampling point, the sample handling and the test method named, the party that carries a missed result named, and a failed result rectified and retested as agreed. Acceptance records are project documents; when you compare quotations, ask for the acceptance section of the contract.
What the figures on this page are, and what is not published
There is no independent performance test for this screen on file, so this page publishes no removal rate and no capacity band. The dimensions, the aperture and the material are project-confirmed values issued on the drawing, not catalogue promises. The selection and sizing guide takes the flow and the downstream requirement through the choice (evidence SH-IF-EVIDENCE-01).
The headworks behind the screen are separate duties. Screens and filtration covers the family selection, grit removal in wastewater treatment covers the grit chamber that sits behind the screen, and the design influent quality chart is the place to start when the feed has not been characterised.
Delivery
Units are assembled and tested at our factory before shipment, then shipped with export documentation. The channel or chamber dimensions and the discharge arrangement are confirmed against the site before the build. Loading arrangement and the delivery schedule are confirmed with each order against the packed dimensions and the port of discharge.

