Container loading calculator: how many units fit a dry container.

Enter the packed length, width, height and weight of one unit. The page returns how many fit a 20GP, 40GP and 40HC dry container, whether volume or payload binds, the volume ceiling where the payload is confirmed per booking, and how many containers a batch needs.

Units per container, binding source and containers needed

Enter one packed unit and its weight. The calculator deducts the packing and lashing allowance, tries both plan orientations, and returns units per container for 20GP, 40GP and 40HC, with the payload line stated for each.

Packed unit dimensions
m
m
m

Measure the packed outer envelope, including crate or pallet — the same basis as the packing and lashing allowance on the container loading chart.

kg

Required. It decides the payload count, which usually binds before the space does for equipment.

Fill this in to get the number of containers a batch needs. Whole numbers only; anything else is ignored.

Result

Units per container are the smaller of the volume count and the payload count. The 40HC payload is set by the carrier and the CSC plate and is confirmed per booking, so its count is a volume ceiling and no payload count is applied.

20GP — 20 ft general purpose

Effective loading space: 5.698 × 2.152 × 2.243 m

Fits the effective loading space

Units per container

1 unit

1 across × 1 deep × 1 high

Volume-bound

Space utilization
32.7%
Weight utilization
12.5%

Net payload estimate 28,000 kg

40GP — 40 ft general purpose

Effective loading space: 11.832 × 2.152 × 2.243 m

Fits the effective loading space

Units per container

3 units

3 across × 1 deep × 1 high

Volume-bound

Space utilization
47.3%
Weight utilization
39.6%

Net payload estimate 26,500 kg (conservative estimate)

40HC — 40 ft high cube

Effective loading space: 11.832 × 2.152 × 2.548 m

Fits the effective loading space

Units per container

3 units

3 across × 1 deep × 1 high

Volume ceiling — payload confirmed per booking

Space utilization
41.6%
Weight utilization
—

Payload set by the carrier and the CSC plate; confirm per booking

Request a sizing proposal

Send the packed dimensions, the unit weight and the batch size, and we confirm the shipping route and the container count.

Data sheet draft

These are catalogue-based figures for your enquiry. Confirm them against your site data and the factory quotation before ordering.

What you entered
  • Packed unit dimensions: 3.0 × 1.5 × 2.0 m
  • Unit weight: 3500 kg
What we derived
  • 20GP — 20 ft general purpose: Units per container: 1 unit
  • 40GP — 40 ft general purpose: Units per container: 3 units
  • 40HC — 40 ft high cube: Units per container: 3 units
Still to confirm
  • Whether the unit can be lifted and loaded in the orientation you entered (skid and lifting points)
  • Road weight limits and permit restrictions on the destination route
  • Crating, sea-fastening and any packaging allowance you want included

Counts assume one unit type per container and the net payload ceilings used here. The factory confirms the loading plan against the actual skid drawing before shipment.

Units per container for three hypothetical sample cargoes

A hypothetical example, not a product list: three sample cargoes are loaded into each container type by the same method the calculator uses. Each cell is the units per container and what binds — volume, payload, or the volume ceiling where the payload is confirmed per booking. The full table is in the page source, so it reads with JavaScript off.

Wide table: scroll sideways to see every column.

ContainerEffective loading space (m)Light cartons 1.2 × 1.0 × 1.2 m, 300 kgCrates 1.8 × 1.2 × 1.6 m, 900 kgDense skids 1.0 × 0.9 × 1.6 m, 3,000 kg
20GP — 20 ft general purpose5.698 × 2.152 × 2.2438 units (volume)4 units (volume)9 units (payload)
40GP — 40 ft general purpose11.832 × 2.152 × 2.24318 units (volume)9 units (volume)8 units (payload)
40HC — 40 ft high cube11.832 × 2.152 × 2.54836 units (volume ceiling; payload confirmed per booking)9 units (volume ceiling; payload confirmed per booking)26 units (volume ceiling; payload confirmed per booking)

Sample cargoes are hypothetical. Effective space deducts 0.10 m on each side of the length and width (0.20 m off each in total) and 0.15 m off the top. Payload is a conservative net-payload estimate: 28,000 kg for 20GP and 26,500 kg for 40GP, derived from carrier maximum payload and rounded down, not a rating. The 40HC payload is set by the carrier and the CSC plate and is confirmed per booking, so its cells are a volume ceiling only and weight is not applied.

What this calculator does

It answers two questions about one packed unit: how many fit a standard dry container, and how many containers a batch needs. Enter the outer length, width, height and weight. The page deducts the packing and lashing allowance, tries the unit length along the container length and across it, keeps the height axis upright, and returns the count for 20GP, 40GP and 40HC.

The count is not a single number. Equipment is heavy cargo, so the payload limit often binds before the space does, and each card says which limit produced its count. The 40HC payload is set by the carrier and the CSC plate and is confirmed per booking, so that card stops at the volume ceiling rather than implying a weight verdict.

The formula

Effective loading space = internal dimensions − packing and lashing allowance. Units by volume = floor(effective length ÷ unit length) × floor(effective width ÷ unit width) × floor(effective height ÷ unit height), and again with the length and width swapped; the larger of the two plan counts wins. Units by payload = floor(payload ÷ unit weight). Units per container = the smaller of the two.

Containers needed = ceil(quantity ÷ units per container). On the 40HC the payload term is not applied, so the count shown is the volume term alone and the reverse count is marked volume only. The rotation rule extends the chart method: the chart divides by the unit length along the container length only, which is its conservative special case.

Basis and assumptions

Every value in the calculator comes from one of the sources below, and each row states which. The nominal internal dimensions and capacities are carrier equipment specifications, not ISO table values; the payload ceilings are conservative net-payload estimates from carrier data, not ratings; the allowance and the loading formula are the site method also published on the container loading chart; the plan rotation and the 40HC treatment are this page's stated decisions. No unconfirmed value enters the calculation: the 40HC payload, the door opening, tare and gross weight, pallet stacking and mixed cargo are all outside this calculator.

ParameterValueSourceEvidence level
Internal dimensions20GP 5.898 × 2.352 × 2.393 m; 40GP 12.032 × 2.352 × 2.393 m; 40HC 12.032 × 2.352 × 2.698 mCarrier equipment specifications; ISO 668:2020 and GB/T 1413-2023 set the class, rating and minimum dimension framework; ISO 1496-1 defines the internal dimensionsExternal reference
Internal volume33.2 / 67.7 / 76.3 m³Carrier nominal capacity, not derived from the rounded dimensionsExternal reference
Net payload, 20GP and 40GP28,000 kg and 26,500 kgConservative net-payload estimates from carrier maximum payload, rounded down; not ratings and not a published rangeEngineering estimate
Net payload, 40HCSet by the carrier and the CSC plate; confirmed per booking; not used in this calculationCarrier equipment specification and CSC plateExternal reference (not used)
Packing and lashing allowance0.10 m on each side of the length and the width (0.20 m off each in total) and 0.15 m off the heightSite method also published on the container loading chart; not an ISO or carrier ruleSite method / engineering estimate
Units per containerfloor(L/l) × floor(W/w) × floor(H/h), with the length and width swapped in plan and the larger count taken; the height axis is fixedSite method; the plan rotation is this page's extension, and the chart's single orientation is its conservative special caseSite method / site decision
Volume against payloadTake the smaller of the volume count and the payload countSite method; equipment is heavy cargo, so the payload usually binds firstSite method
Route classificationWidth 2.2 m; height uses the actual door opening and the booking confirmationSite route-classification rule; not a fit guarantee and not an ISO or carrier limitSite method

Worked example

A unit of 3.0 × 1.5 × 2.0 m weighing 3,500 kg. In a 20GP the effective space is 5.698 × 2.152 × 2.243 m, which takes 1 unit (volume-bound), 1 across × 1 deep × 1 high, using 32.7% of the space and 12.5% of the payload. In a 40GP it takes 3 units (volume-bound), 3 across × 1 deep × 1 high, using 47.3% of the space and 39.6% of the payload. In a 40HC it takes 3 units as a volume ceiling, because the payload is set by the carrier and the CSC plate and is confirmed per booking.

A 16 × 3.0 × 3.5 m unit weighing 12,000 kg fits no dry container in any of the three: it is longer than the 11.832 m effective length of the 40 ft containers, wider than the 2.152 m effective width and taller than the effective height. Units wider than the 2.2 m route-classification threshold need a route check with the forwarder.

For a batch of 12 of the 3.0 × 1.5 × 2.0 m units, a 20GP needs 12 containers, a 40GP needs 4, and a 40HC shows 4 containers volume only — payload confirmed per booking. Every figure above is the output of the calculator on those inputs.

Limits

The calculator counts identical units against the container envelope and the net payload ceilings used here; it is not a lashing, centre-of-gravity or booking plan.

  • Identical units only. Mixed cargo — several different sizes in one container — is not modelled.
  • Box tare and gross weight limits, overweight and oversize surcharges are not included; the payload figures are net payload only.
  • The door opening is smaller than the internal height; confirm it with the forwarder.
  • The height is computed as stackable layers, while monobloc equipment usually travels in one layer — set the layer count against the forwarder's plan.
  • No lashing or centre-of-gravity check. The container and the stow are confirmed with the forwarder.
  • The 40HC payload is set by the carrier and the CSC plate and is confirmed per booking. Its result is a volume ceiling and carries no weight verdict.
  • The result is an estimate for the enquiry; the booking confirmation and the forwarder's plan govern.

Tell us what the site has to treat.

Contact details
Tell us about your project